سیستم های کفپوش اپوکسی

سیستم های کفپوش اپوکسی

کفپوش های اپوکسی



Epoxy - Colored Vinyl Flake Broadcast Flooring System

Part 1: General    

1.01    System Description

A.    Roller-applied 100% solids, penetrating epoxy primer followed by a 100% solids epoxy basecoat, a broadcast of decorative colored vinyl flakes and sealed with a 100% solids epoxy grout.  Optional urethane topcoats may be applied for additional chemical and abrasion resistance.

B.    This system shall be applied to the prepared substrate(s) as defined by the plans strictly in accordance with the manufacturer’s recommendations.

1.02    Submittals

A.    Product Data
1.  Current edition of manufacturer’s product literature including physical data, chemical resistance, surface preparation, and application instructions.

B.    Samples
1.  A hard sample of the proposed system shall be submitted to represent the finished floor.

C.    Warranty
    1.  Manufacturer’s standard warranty
    2.  Applicator’s standard warranty

1.03    Quality Assurance

A.    Qualifications
1.  The manufacturer shall have a minimum of ten (10) years’ experience in the production, sales, and technical support of polymer-based floor coatings.

2.  The applicator shall have a minimum of three (3) years’ documented experience in the application of polymer floor coatings to concrete floors and be approved by Florock.

3.  Proposed suppliers products shall provide certification that they have ten (10) years’ experience in the production of polymer floor coatings and be required to meet all provisions of this specification as well as provide evidence for compatibility between components to the satisfaction of the Architect.

B.    Pre-Bid Conference
1.  A pre-bid conference should be held between prospective applicators and the Architect to review surface preparation, application, clean-up procedures, and design issues.


C.    Packing and Shipping
1.  All materials are to be delivered to the job site in the manufacturer’s original packaging. The product code and other identification marks should be clearly marked and visible.

D.    Storage and Protection
1.  All material is to be stored in a cool, dry place out of the direct sunlight and away from any ignition sources. The applicator should refer to the manufacturer’s literature and Material Safety Data Sheets for more information.

2.  Material Safety Data Sheets are to be kept on site and made readily available for all personnel.

3.  Keep containers sealed and ready for use.

1.04    Project Conditions
 
A.    Environmental Requirements
1.  Optimum air and substrate temperature for product application is between 55° F      (13° C) and 95° F (35° C).  For temperatures outside of this range, consult the manufacturer for product application suggestions.

2.  Verify the work environment is properly equipped with vapor barriers and perimeter drains.

3.  Maintain proper lighting throughout the work environment; the lighting should be comparable to the final lighting level of the space.

4.  Store and dispose of any waste in accordance with regulations of local authorities.

B.    Safety Requirements
1.  “No Smoking” signs shall be posted throughout the work area prior to application.

2.  The owner shall be responsible for removing any foodstuffs from the work area.

3.  Open flames, spark producing tools/items, and ignition sources shall be removed from the work area prior to application.

4.  Only work-related personnel shall be allowed within the work area.

1.05    Warranty

A.    Coordination
1.  The manufacturer offers a full, one-year warranty against defects in materials. Warranties concerning the installation of the material are solely the responsibility of the applicator.




Part 2: Products

2.01    Manufacturer

A.    Crawford Laboratories, Inc.
4165 South Emerald Avenue
Chicago, IL 60609
Phone: (773) 376-7132; (800) 356-7625
Fax: (773) 376-0945
http://www.florock.net

2.02    Materials

A.    Primer
1.  The primer shall be a 100% reactive, epoxy-based, penetrating primer that exhibits chemical resistance:  Floropoxy 4700 Epoxy Primer.

B.    Basecoat & Broadcast
1.  The basecoat shall consist of chemical resistant, self-leveling, 100% solids Floropoxy System 4805 (pigment this coat to compliment the chip color).

2.  Broadcast colored vinyl flakes to achieve the desired appearance. Use Florock FloroChips.

   C.       Grout Coat
       1.  Grout with a 100% solids, chemical resistant, clear, Floropoxy 4805.

   D.       Optional Topcoat
    1.  Apply 1 to 2 topcoats of a Florock high performance, color-stable, chemical resistant urethanes, exhibiting excellent chemical and abrasion resistant properties.
 

تصاویر سیستم های کفپوش اپوکسی